This Kit is very easy to build , no solder work any more, just assemble then plug and play .
Very cheap but equipped with high-performance and stable components. The frame is formed by high-precision TPU 3D printing, fixed with carbon fiber board and the use of integral foam to prevent collision. Every FPV pilots could enjoy the fun of building their own FPV Cinewhoop.
Features:
No Solder work need and easy to build
Very reliable and resistant to drops
Stable and smooth flying
Insta360 fixed mount ready
Smooth and powerful
Diversity SPI Receiver compatible Frsky/S-FHSS/Redpine protocol
Specifications：
Brand Name: Happymodel
Item Name: Cine8
Wheelbase: 85mm
Size: 145mmx140mmx23mm
Weight: 73g(without battery)
Weight: 99g(with Insta360)
Motor Mode: EX1202.5 KV8000
Configu-ration:9N12P
Stator Diamter:12mm
Stator Length:2.5mm
Shaft Diameter:Φ1.5mm
Motor Dimension(Dia.*Len):Φ14mm*14.5mm
Weight(g):4.4g
No.of Cells(Lipo):2-3S
Propellers Material:PC
Weight:0.91g
Pitch:2in
Props Dia:50.3mm
Center Thickness:4.5mm
Center Hole Dia:1.5mm 3 holes
Flight controller (Frsky SPI RX version) CrazybeeF4 V3.1 AIO FC Firmware target: MATEKF411RX
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 2-4S battery input (DC 7V-17V)
Built-in 20A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5V 1A BEC
Onboard 4in1 ESC MCU upgraded to EFM8BB21
Power supply: 2-4S LiPo/LiPo HV (7v/17v)
Current: 20A continuous peak 25A (5 seconds)
Support BLHeliSuite programmable
Factory firmware: F_H_40_REV16_8.HEX
Default protocol: DSHOT600
Onboard Frsky SPI D8 receiver Version CC2500 Hardware
Compatible with FrskyD FrskyX Frsky_X_LBT SFHSS REDPINE protocol
Channels: 8ch
Failsafe support
Diversity 2.4G receiver system
No ground interference: above 300meter
5.8G 400mw VTX Output power: 25mw~400mw switchable
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 400mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race bandSmartAudio ready
Caddx ANT 1200tvl camera Image Sensor: 1/3″ CMOS Sensor
Horizontal Resolution: 1200 TVL
TV System: NTSC or PAL
IMAGE: 16:9 or 4:3
Synchronization: Internal
Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
S/N Ratio : >52dB (AGC OFF)
Video Output: CVBS
Lens: 1.8mm
Min. Illumination: 0.001Lux@F1.2
Auto Gain Control: YES
BLC: YES
WDR: Global WDR
DNR: 3D DNR
Dimensions: 14*14mm(with bracket to 19*19mm)
Wide Power Input: DC 3.7-18V
Work Temperature: -20℃~+60℃
Weight: 2g (N.W.)
Lipo Battery Capacity:450mAh
Voltage:11.1v
Continuous Discharge Rate: 75C
Size: 66mmx21mmx18mm
Weight: 45g
Connector: XT30
Cine8 Frame 1
3D print TPU Insta360 go fixing mount for CINE8 1
CrazybeeF4 V3.1 SPI Receiver version compatible FrskyD8/D16 S-FHSS 1
Happymodel EX1202.5 KV8000 brushless motor 4
Gemfan D51(2020-4) Cinewhoop Props 1
Caddx Ant 1200TVL Global WDR with OSD 2g Ultra Light Nano FPV Camera 1
5.8G 25mw~400mw Whoop_VTX_HP 1
TypeC USB Adapter 1
Tattu 3S 11.4V 450mah battery 1
and then Add to Home Screen.